Page Comparison

Diagnostics - Troubleshooting Cell Interface (ppp0), Check Signal Strength

...

================ Main Menu ==============

ElecSys(V:5.7.2017-02-23-1000)  Thu Mar  2 18:09:02 2017

RediGate400C_CPLX : 1 @ 10.63.192.192  REDIGATE-400 <Use System Serv Option-123>

---------------------------------------------

 1) System      Services

 2) Directory   Services

 3) Diagnostics Services

 

99 Log Off

 

Enter '1' for System Services.

Make selection: 1

 

================ System Services ==============

ElecSys(V:5.7.2017-02-23-1000)  Thu Mar  2 18:09:07 2017

RediGate400C_CPLX : 1 @ 10.63.192.192  REDIGATE-400 <Use System Serv Option-123>

---------------------------------------------

 1) Boot/Reconfigure     2) Set Clock

 3) Channel Status       4) Channel Enable/Disable

 5) Channel Scan         6) Single Poll

 7) RTU Enable/Disable   8) RTU Scan

 9) RPN Calculator      10) New Master Key

11) Read Handshake Pins 12) Write Handshake Pins

13) Run Custom Utility  14) MQttClient to Next Broker

15) Cell Modem Diags

 

Enter '15' for Cell Modem Diags.

Make selection: 15

 

================  Cell Modem Diags  ==============

ElecSys(V:5.7.2017-02-23-1000)  Thu Mar  2 18:09:19 2017

RediGate400C_CPLX : 1 @ 10.63.192.192  REDIGATE-400 <Use System Serv Option-123>

---------------------------------------------

 Virtual Port Numer

   73=Diag AT Cmds

   75=Auto-ATs or NMEA/GPS if HE-910

   77=NMEA/GPS if DE-910

   79=CellLEDs

Enter '73' for the virtual port number. After this, the RediGate will automatically request several AT commands from the modem.

This information provides some modem and activation information (see the Diagnostics Manual for more detail on the output of these commands).

 or 0 to Exit? 73

Sending AT+GMM

Received[15]->   HE910    OK

...

A properly configured RediGate 400C with 2 enabled ethernet ports and a cellular connection is shown below, with addresses for eth0, eth1, and ppp0 (cellular).

<<<< ElecSys Linux RediGate 400 >>>> Name: (RediGate400C) Unit: (1) Eth0-IP: 0.0.0.0 armv5tel RediGate400C.(none) 3.12.9-00044-g5a52a4b

RediGate400C login: root
Password:
Hello root. Your path is /bin:/sbin:/usr/bin:/usr/sbin:/usr/bin/X11:/usr/local/bin:/usr/director/bin

[root@RediGate400C ~ ]$ ifconfig
eth0 Link encap:Ethernet HWaddr E2:E0:32:B5:ED:32
inet addr:10.63.192.151 Bcast:10.63.255.255 Mask:255.255.0.0
inet6 addr: fe80::e0e0:32ff:feb5:ed32/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:15148 errors:0 dropped:29 overruns:0 frame:0
TX packets:57 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2015623 (1.9 MiB) TX bytes:5017 (4.8 KiB)

eth1 Link encap:Ethernet HWaddr E2:E0:32:B5:ED:32
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::e0e0:32ff:feb5:ed32/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:11 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:878 (878.0 B)

eth_base Link encap:Ethernet HWaddr E2:E0:32:B5:ED:32
inet6 addr: fe80::e0e0:32ff:feb5:ed32/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:15148 errors:0 dropped:0 overruns:0 frame:0
TX packets:84 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2348879 (2.2 MiB) TX bytes:7467 (7.2 KiB)
Interrupt:64 Base address:0x8000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

ppp0 Link encap:Point-to-Point Protocol
inet addr:166.130.92.39 P-t-P:166.130.92.39 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:25 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:880 (880.0 B) TX bytes:135 (135.0 B)

...